General Purpose Distribution Transformers
HPS's line of single phase and three phase general purpose distribution transformers are rated for 600 volts and below. They are generally used for supplying appliance, lighting, motorized machine and power loads from electrical distribution systems. They are either ventilated or totally enclosed, and are available with either aluminum or copper windings in standard ratings from 50 VA up to 750 kVA. Shielded distribution transformers are also available, which provide a copper electrostatic shield between the primary and secondary windings. The shield is grounded and thus shunts most noise and transients to the ground path rather than passing them through to the secondary. Applications for shielded transformers are similar to those above, and are ideal for commercial or electrical installations where electronic circuitry operating at low voltage DC is present and is very sensitive to 'noise'.

Back to Top

Encapsulated General Purpose Transformers
HPS's line of single phase and three phase general purpose encapsulated transformers are rated for 600 volts and below. Encapsulated transformers are standard general purpose distribution transformers encased in a electrical grade silica and epoxy, and totally enclosed in a heavy duty NEMA 3R style enclosure. All leads are brought out to a separate front accessible termination compartment. All encapsulated transformers are available with copper windings in single phase ratings from 0.05 kVA up to 37.5 kVA and three phase ratings from 2kVA up to 45 kVA. Typical applications of encapsulated transformers are pulp and paper plants, steel mills, food processing plants, breweries, mines, marine and shipboard installations etc. Electrostatic shields, a copper electrostatic shield between the primary and secondary windings, are standard on single phase units above 0.50 kVA and optional on most others.

Back to Top

Non-Linear (K-Factor) Distribution Transformers
The use of electronic equipment has continued to grow in both offices and industrial plants. Either switching power supplies or rectifier circuits power these electronic devices. Examples of these devices include computers, fax machines, copiers, printers, cash registers, UPS's and solid-state ballasts. They all contribute to the distortion of the current waveform and the generation of Harmonics. General purpose transformers, most frequently used for applications such as commercial or institutional buildings, will, by definition, supply widely varied single phase loads as described. K-Factor transformers are general purpose transformers but are designed to tolerate the harmonic distortion associated with these loads.

Back to Top

Energy Efficient (TP1) Distribution Transformers
HPS is pleased to introduce a line of energy efficient,
dry-type, general purpose distribution transformers to meet NEMA TP-1 specifications. In the past several years, there has been an accelerated rate of change to introduce energy efficiency standards for transformers in North America. Many products have preceded the initiatives for transformers in an overall effort to optimize manufactured goods for environmental concerns. Governments are encouraging users to consider energy efficient products like dry type transformers, in an effort to help reduce carbon dioxide emissions. In addition to the benefits to the environment, energy efficient transformers also can realize substantial savings in operating costs thereby having a direct impact on the initial investment evaluated over a period of

The US Energy Policy Act of 2005

Introduction to TP1 Legislation

Energy Policy Act 2005 - Transformer Summary

Part 431 - Energy Efficiency Program for Certain Commercial & Industrial Equipment

HPS and the impact of EPACT 2005 explained - presentation

Back to Top

Drive Isolation Transformers
With today's technological advances in solid-state power control devices, the use of AC and DC variable speed drives has proliferated in many industrial markets. General purpose distribution transformers are not adequate for this type of application. HPS's Drive Isolation transformers are designed to meet the rugged demands of both AC and DC variable speed drives and also to provide the required voltage change. The separate primary and secondary windings provide electrical isolation between the incoming line and the SCR load. The windings are designed to withstand overcurrent of 150% of the rated load for 60 seconds or 200% of the rated load for 30 seconds. A duty cycle of one start for every two hours is permitted. Drive Isolation Transformers are sized to match standard motor horsepower and voltage ratings. Standard sizes range from 5 to 600 HP in six standard voltages in both aluminum and copper. Nonstandard sizes and voltages are available upon request.

Back to Top

AutoTransformers
HPS three phase autotransformers are available for applications where small voltage corrections are necessary in a distribution system. They are frequently used as an economical alternative to three phase general purpose distribution transformers to adjust the supply voltage to match specific load requirements when load isolation from the supply line is not required. Autotransformers can be used as either a step-up or step-down transformer. Available with either aluminum or copper windings in ratings from 3kVA to 500kVA.

Back to Top

Custom/Specialty Distribution Transformers
HPS custom distribution transformers are designed and constructed to meet or exceed the requirements of our standard distribution transformer general applications. These transformers are provided either ventilated or totally enclosed. To meet special applications and requirements, custom/specialty designs are available to meet your specific application needs. If you have a need for one of these types of transformers, but do not see it listed here or in our related catalog, please either complete the custom distribution transformer specification form or send your detailed request to our quotations department and they will respond to it within 48 hours.